Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

Mitigation of the blast load effects on a building structure using newly composite structural configurations

In this study, a nonlinear three-dimensional hydrocode numerical simulation was carried out using AUTODYN-3D to investigate the effect of blasting of a high explosive material (TNT) against several configurations of the composite structure. Several numerical models were carried out to study the effect of varying the thickness of the walls and the effect of adding an air layer or aluminum foam layer inside two layers of concrete in mitigating the effect of blast waves on the structure walls. The results showed that increasing the thickness of walls has a good effect on mitigating the effect of blast waves. When a layer of air was added, the effect of blast waves was exaggerated, while when a layer of aluminum foam was added the blast wave effects were mitigated with a reasonable percentage.     

德文版液压系统模拟仿真软件的汉化方法

介绍了德文版的 Fluid SIM-H液压系统模拟仿真软件 ,并介绍了应用 Exe Scope、Help Deco、Help Work和 Create Install等工具软件对德文版软件进行汉化的基本方法     

图像处理技术在消防灭火模拟训练中的应用

阐述了应用图像处理技术构建消防灭火模拟训练系统的方法,对其中的技术要点从原理上进行了说明。提出了一种基于目标信息特征的灰度Hough变换实用加速算法用于直线检测,使其运算量比传统算法下降了4个数量级。实验结果证明这种检测与提取灭火水柱中心线的方法快速、有效。用该方法构建的系统,经实际运行证明是图像处理技术在消防灭火模拟训练方面的一个成功的应用。     

应用最大熵谱估计进行导弹系统的仿真模型验证

探讨了导弹系统仿真模型验证的定量方法。依据最大熵谱估计方法分辨力高的特点，分析其近似统计特性，分别给出了两个样本和两个正态总体的一致性检验方法。仿真结果表明，利用最大熵谱估计进行有效性检验是可行的。最后给出了一个应用实例，应用谱估计方法进行寻的制导导弹数字仿真模型验证     

功率循环下IGBT模块电热参数变化规律分析

为了分析IGBT模块老化过程中电热参数的变化规律,对IGBT模块进行了功率循环加速老化试验,并基于单脉冲测试方法在加速老化试验进程中每间隔1 000次功率循环,测取一次IGBT的结温、集电极电流与饱和压降三维关系曲面、开关能耗、热阻抗以及瞬态热阻抗曲线。IGBT模块老化失效时,其饱和压降、开通能耗、关断能耗以及热阻较其初始值分别增大了3.92%、12.05%、18.87%和22.65%,试验结果表明随着IGBT模块功率循环次数的增多,相同工作条件下IGBT饱和压降的增幅逐渐加大,而饱和压降、结温和集电极电流三者间的内在关系没有明显变化;IGBT瞬态热阻抗曲线暂态部分几乎不变,稳态部分向上移动的幅度逐渐加大;测取的IGBT模块电热参数中饱和压降增幅最小,开关能耗增幅较大,模块热阻的增幅最为明显。     

制冷空调系统的模糊控制与模拟仿真

在制冷空调系统中采用电子膨胀阀（ＥＸＶ）代替传统的热力膨胀阀后,为各种调节控制技术的应用提供了广阔的前景．作者介绍了模糊控制器的设计及在制冷空调系统中的应用前景,并通过Ｍａｔｌａｂ工具包中的Ｓｉｍｕｌｉｎｋ软件进行模拟仿真,验证了模糊控制器的控制特性．     

基于DSP机动目标自动跟踪仿真系统设计

从硬件角度叙述了机动目标自动跟踪仿真系统设计的几个问题.系统由两片超高速信号处理芯片(TMS320C30)组成并行系统,计算容量大,既能脱机运行,又能在微机的监控下工作,为机动目标的实时跟踪计算、状态滤波估计和解命中等问题的仿真研究,提供了方便、灵活的硬件环境.     

身管振动中摇架支承的分析

将摇架支承简化为移动约束,分析了这种支承简化对火炮身管振动的作用并进行了数值模拟,并讨论了摇架支承对炮口扰动的影响。     

Client/Server 模式的智能语言集成框架

将ＡＩ技术集成到主流信息技术之中是提高信息系统智能化水平的一项十分重要的基础性工作。本文讨论一种Ｃｌｉｅｎｔ／Ｓｅｒｖｅｒ计算环境（简称ＣＳＥ）,它将Ｐｒｏｌｏｇ系统和Ｃｌｉｐｓ系统作为两种特殊的数据服务系统集成其中。ＣＳＥ支持客户应用使用确定的ＡＰＩ,以规范的Ｐｒｏｌｏｇ语言（或Ｃｌｉｐｓ语言）形式请求Ｐｒｏｌｏｇ服务器（或Ｃｌｉｐｓ服务器）提供问题求解服务。文章阐述了这一设计的合理性,讨论了ＣＳＥ的体系结构和实现技术,说明了与特殊数据服务无关的通信机制、ＡＩ语言服务器的挂接技术以及ＣＳＥ应用。